Fibertel helps with fiber installation in homes and projects - from blowing in microduct/ducts to tidy preparation in technical rooms or cabinets. We work with clear checkpoints and deliver labeling and documentation so the installation is easy to finish, operate and troubleshoot.
Service area: Vestfold, Telemark and Buskerud (other areas by agreement).

When do you need fiber blowing?

• When fiber needs to be installed in microduct/ducts to a house, townhouse or new buildild
• When you want fiber brought into a technical room/cabinet for a tidy installation
• When the duct route is long, has many bends, or pulling is difficult
• When a repair/relocation requires new fiber in existing ducts
• When you want termination/prep, labeling and documentation after installation
• When fiber is damaged - e.g., after digging in the garden, site work, drainage or construction incidents
• When fiber is damaged during renovation - drilling, wall pulling, remodeling, moving the technical cabinet, or rebuilds

How we work (equipment and method)

We choose method and equipment based on route, duct/microduct type, length and number of bends - focusing on stable installation, low risk and good control.

This can include:
• Review of route, duct/microduct and entry point
• Assessment of pulling vs blowing (based on conditions)
• Preparation in technical room/cabinet (order, labeling and structure)
• Documentation of route and delivery (by agreement)

FPT KAT Mini

FPT KAT Mini is typically used when we need a compact and flexible blowing unit on site - for example in cabinets, at handholes/manholes, or where rig space is limited.

• Blowing in microduct and smaller ducts where precise control matters
• Service and partial sections (in/out of cabinets, distribution points, technical rooms)
• Jobs with short changeovers and limited space

What this means for you

• Suitable when there are many points/sections in the same area
• Practical in tight conditions and the “last meters” into the technical room/cabinet

Fiber into the home - from duct/microduct to your technical room

Building new, upgrading, or need fiber into a technical room/cabinet? We can help with routing in duct/microduct, control and tidy documentation - making termination and final completion easier.

👉 Send a request

Tell us what you need in a few lines, and we will reply with clear next steps.

FPT KAT Micro is used for microduct blowing where stable installation and efficient production are required.

Typical use cases

• Microduct-based routes in rollout projects
• Routes with multiple sections and multiple entry points
• Work where consistent production flow and repeatable setup is important

What this means for you

• Predictable progress when the route and prerequisites are clarified
• A good option when the project requires multiple blowing operations

Jetting VO HD is used for jetting/installation where method and setup are adapted to the route and desired duct installation - especially when conditions require extra control.

Typical use cases

• When jetting is the right method for the project
• Where stability and control of the installation is critical
• Jobs where equipment and method must be adapted to local conditions

What this means for you

• An additional method choice when the project needs more than “standard blowing”
• Useful when route condition, duct condition and execution are decisive

We follow a clear, checkpoint-based process. This reduces deviations and provides a delivery that’s easy to follow up.

1) Clarification before start

• Review of route, duct/microduct and access
• Clarification of lengths, bends and any splice points
• Agreement on labeling and documentation

2) Setup and preparation

• Setup at blowing point and receiving point
• Route/duct verification (where possible/by agreement)
• Preparations for safe and tidy execution

3) Installation (blowing/jetting)

• Controlled installation with method adapted to conditions
• Ongoing checks to ensure stable progress and avoid damage

4) Finish and handover

• Preparation for splicing/termination (according to project plan)
• Order and labeling in cabinet/technical room
• Documentation delivered in the agreed format

Documentation is adapted to project requirements and interfaces with main contractor/client. Typical deliveries:

• Labeling and traceability along the route and at distribution points (by agreement)
• Overview of completed sections and deliveries on site
• Basis for further splicing/termination and “as-built” (when included in scope)

If you have specific documentation requirements, we align early in planning - so the delivery is correct the first time.

See examples of completed deliveries and project work here:

▶ Video library
▶ Fiber blowing / jetting
▶ Photo gallery

Fibertel delivers fiber and telecom infrastructure in Vestfold, Telemark and Buskerud from routing in duct/microduct to tidy labeling and documentation.